One by-product of combustion is carbon, the black soot that can collect and harden on the cylinder head, cylinder wall, piston and valves. Carbon deposits in the combustion chamber can affect engine performance, resulting in higher oil consumption, engine knocking or overheating.
Using unleaded gasoline reduces carbon deposits, but you should still remove the cylinder once each 100 hours of operation and scrape off the carbon, using the tools and solvents described in this section. Clean the cylinder more frequently if you use your engine heavily.
Removing Engine Components
The first step in servicing the cylinder head is reaching the cylinder head. You may need to remove some other components first.
Remove the muffler, muffler guard and any
other components that block access to the cylinder.
Cylinder head bolts near the muffler and
exhaust port may be longer. To avoid confusion, prepare a
template. Draw a rough outline of the cylinder head on a piece of
cardboard and punch holes for each bolt location. Then, remove the
cylinder head bolts and insert them in the corresponding holes.
Remove each cylinder head bolt and store it in its respective slot in the cardboard until you are ready to reinstall the cylinder head (image A).
Lift off the cylinder head. If the head sticks, strike it on the side with a nylon-faced hammer. This should loosen the cylinder head enough for your to gently lift if off the engine. NOTE: Do not pry off the cylinder head. This can damage the surface of the engine block or the cylinder head.
Remove and discard the old head gasket (image C).
Removing Carbon Deposits
Always wear protective eyewear and solvent-proof gloves when removing carbon. Ask your Authorized Dealer to recommend an all-purpose solvent that will not harm aluminum or plastic components or leave unwanted residues.
Place the piston at the top dead center so that the valves are closed. Then, scrape carbon gently from the cylinder head, using a wooden or plastic scraper. Take care not to dig the scraper into the aluminum. On stubborn deposits, use a putty knife, wire brush or steel wool (images A, B, and C),
taking care not to bear down on the metal surfaces.
Clean away the remaining carbon with
solvent, using fine steel wool to smooth rough spots. You can also
soak metal parts for up to 15 minutes to remove stubborn deposits.
Scrape again, if necessary, to loosen stubborn grit. Then, clean
the area thoroughly with the solvent and set the head aside.
With the piston still at the top of the cylinder and the valves closed, use the same method to remove carbon deposits from the piston and the end of the cylinder (image C).
Turn the crankshaft to open each valve, and carefully remove any visible carbon deposits on the valves and valve seats (image D), using only a brass wire brush. CAUTION: Do not allow grit to fall into the valve chambers or between the piston and the cylinder wall (image E).
Inspect the valves and valve seats to see
if they are cracked, rough or warped. Bring damaged parts to an
authorized service dealer for inspection before reassembling the
Using a scraper, solvent or both, remove any remaining carbon and residue left behind by the head gasket on the cylinder head and engine block. Clean the surfaces thoroughly before installing the new head gasket. Any debris or oil left on the cylinder head or engine block may prevent a tight seal and cause eventual engine damage.
Reassembling The Cylinder Head
Inspect the surfaces of the engine block,
cylinder head and new head gasket to be sure they are clean.
Place the new head gasket in position on
the engine block. Do not use sealing compounds.
Set the cylinder head on the head gasket,
aligning the cylinder head with the gasket and the engine block.
Remove each head bolt from its slot in the cardboard template (image F). Then, insert the bolt in its original location, leaving it
loose. Insert the other bolts in the same fashion. Make sure to
attach any housings or brackets that are held in place by the head
Hand-tighten the head bolts first,
without using a wrench.
Tighten the cylinder head bolts in increments, using a torque wrench. Turn each bolt a few turns, then proceed to the next bolt until each bolt is just snug. For final tightening, use a torque wrench. Proceed in increments or roughly one-third the final torque. Consult the Engine Check Chart for final torque specifications. Avoid tightening a single bolt all the way before tightening the other bolts. Uneven tightening is likely to warp the cylinder head.
NOTE: Please read and abide by any applicable Safety Information (PDF) before performing any engine work.
This information is not meant to take the place of work performed by a Briggs & Stratton Authorized Dealer. Terms and Conditions apply to all of our information provided on this website. Always be sure to read and understand your engine Operator's Manual.